About the TSD-I Voltage Stabilizer
The TSD-I Voltage Stabilizer is part of the ELEHPD UPS And Stabilizer range. General TSD-I intelligent type AC voltage stabilizer TSD-I series intelligent AC voltage stabilizer, which is developed by our company adopts 8 - position CPU manufactured by the world-famous Samsung Company. It has kinds of protections against time-lag, over-voltage, under-voltage, overload and excess temperature and so on, uses hanging type installation for requiring small area. Besides, its soft appearance gives us a favorable visual feeling. ELEHPD manufactures and exports low voltage electrical products from Yueqing, Zhejiang, China, supplying distributors, panel builders, M&E contractors and OEM buyers worldwide.
Typical applications
- Industrial control panels and PLC power rails
- LED drivers, signage and display power
- Battery charging and DC backup systems
- Motor drives, welding sets and rectifier assemblies
- Instrumentation and test equipment
How to specify the right UPS And Stabilizer
- Size the output current with at least 20-30 % headroom over the load
- Check the input range covers the local supply, including brown-outs
- Confirm the enclosure and cooling method for the panel temperature
- Verify the protection set: over-current, over-voltage, thermal and short circuit
Specifications
![]()
| General TSD-I intelligent type AC voltage stabilizer |
|
TSD-I series intelligent AC voltage stabilizer , which is developed by our company adopts 8 - position CPU
manufactured by the world-famous Samsung Company. It has kinds of protections against time-lag, over-voltage,
under-voltage, overload and excess temperature and so on, uses hanging type installation for requiring small area.
Besides, its soft appearance gives us a favorable visual feeling.
|
| Application (TSD-I intelligent type ac voltage stabilizer |
For office equipment, testing equipment, medical equipment, industrial automation equipment, household
appliance, lighting system, communication system, etc. |
| Performance TSD-I intelligent type ac voltage stabilizer |
| lnput voltage |
Single-phase 150V-270V |
Delay time |
Long 180S,short 5s |
| Output voltage |
Single-phase 220v |
Overload protection ＆#118alue |
1.05times of rated power/60s
1.4times of rated power/5s
2times of rated power/0s |
| Accuracy of voltage stabilization |
±5% |
Excess temperature rotection ＆#118alue |
100℃ |
| Frequency |
50Hz/60Hz |
Ambient temperature |
-5℃--+40℃ |
| Adjusting time |
<1s (when input voltage has a change of 10%) |
Relative humidty |
≤90% |
| Efficiency |
>90% |
Waveform distortion |
No additional waveform distortion |
| Over-voltage Protection ＆#118alue |
①250Vdelay5S;②275V/delay 2s③295V/delay 1s④305V/0s |
Load power factor |
0.8 |
| Dielectric strength |
1500V/min |
| under-voltage protection ＆#118alue |
180V/delay 5s |
lnsulation resistance |
≥2MΩ | |
| Model and spec TSD-I intelligent type ac voltage stabilizer |
| Spec(KVA) |
Product size D×W×H(cm) |
Product size D×W×H(cm) |
Weight(kg) |
Qty |
| TSD-I-3KVA |
37×25×13 |
42×3218 |
12 |
1 |
| TSD-I-5KVA |
43×30×14 |
49×36×19 |
18 |
1 |
| TSD-I-8KVA |
48×32×19 |
52×38×25 |
25 |
1 |
| TSD-I-10KVA |
48×32×19 |
52×38×25 |
28 |
1 | |
Frequently asked questions about the TSD-I Voltage Stabilizer
How much headroom should I leave on the power rating?
For continuous industrial duty plan on 20-30 % headroom above the measured load. For loads with high inrush, such as motors or capacitive input, allow more and check the surge rating rather than only the average current.
Do these units accept 110 V and 230 V mains?
Input ranges are model-specific and shown in the specification table. Where a wide-range input is available it is stated; otherwise send your mains voltage and we will match the model.
What protection features are built in?
Typical protection covers short circuit, over-current, over-voltage and thermal shutdown. The exact set is listed per model in the specification table above.
Can you supply matching DIN-rail or enclosed versions?
Open-frame, enclosed and DIN-rail variants exist across this family. Send the model you are working from and we will confirm the equivalent mounting option.
Further reading
